Latest News
- What should I take camping with my boyfriend and I?
- How much would a used, natural gas onan generator be worth?
- is kohler and campbell a good brand for pianos?
- want to assemble electric generators at home need someone to buy parts from ?
- Where Can I purchase a Caterpillar Machine in the United States?
- What should I take camping with my boyfriend and I?
- How much would a used, natural gas onan generator be worth?
- is kohler and campbell a good brand for pianos?
- want to assemble electric generators at home need someone to buy parts from ?
- Where Can I purchase a Caterpillar Machine in the United States?
Google Adsense is here
alternative and bill Briggs build caterpillar diesel DIY efficiency efficient electric electricity eliminate emergency ENERGY Engine FREE gas generate Generator generators green grid home homemade house how instructions kohler machine magnet MAGNETIC make Motor onan Power Renewable review save solar Stratton technology to TURBINE wind
Rolls Royce Olympus II
Posted by admin
Perfect test run of a very large turbine engine at S&S Turbines open-air test cell in Fort St John, BC.
Special guest appearance by Moto Steve, who is the lead hand at Maddex Turbines, where this engine was repaired and tuned up.
Today we made 27 thousand horsepower with this beast. Plenty more on the stick, as it’s rated at 40,000 full on.
Duration : 0:11:42
New Engine Set up Guide Vid 5/8-Engine priming and starting
Posted by admin
Check out Squirrels forum! http://forums.thetoyz.com
Have a new engine? Want to know what to do first on installation? Or maybe you want to find out your needle settings before you start to mess with them (IE: how to go back)? What is the best fuel? What glow plug to use? Ever wonder or to take the engine apart, clean it, and seal the engine from damaging air leaks? Ever wonder how to install the engine or how to set gear mesh? What about break in? Or starting issues and common engine failures? How about tuning?
If you answered yes to any of the above then THIS IS THE VID FOR YOU!
This is vid 5 of an 8 part video series. In this video you will learn how to prime any nitro engine and start any nitro engine. Be it a starter bump box, roto/ tiger drive, ez start, pull start, and more!
Duration : 0:8:13
Briggs & Stratton IC Engine Pt2 - Head Shaving and Cold Start
Posted by admin
Since it is a damaged motor I figured it would be worth experimenting with it, my dad suggested shaving the head down as far as I can on the lathe, and so far it worked!
if I go much lower I will have the valves hitting the head as they open!
Duration : 0:9:39
Antique Briggs and Stratton Engine Model L1 LI Running
Posted by admin
I just bought this off of eBay a couple of weeks ago. It had a good spark and a little compression so I decided to try to start it. Well it didn’t. First off, it didn’t have a gas tank. I felt pretty stupid…
Anyway, I got a gas tank for it, but then the carburetor fitting threads stripped out. They were beyond repair. I debated whether or not to tap them, but that would probably crack the pot metal. So I had to buy a new carburetor.
Once I put that on, I decided that I should take the head off to inspect the bore, head, and gasket before I tried to start it. Two of the 6 head bolts snapped off. I wasn’t too happy. I got one out by pipe wrench because it was sticking out enough to grab hold of it. The other one wasn’t that easy. I tried to weld a nut to the part that was visible, but that snapped the bolt off even more. I really wasn’t happy. So as a final resort, I decided to drill the head bolt out. I didn’t have a big enough drill press to allow enough clearance for the engine (and I didn’t want to pay for a machine shop to do it) so I used a portable drill. I used a 1/8″ bit first, then 1/4″. I saw part of the threads exposed, so I tapped the hole. It wasn’t pretty, but hey, it holds…
The head, gasket, and bore were all fine.
So it started up pretty easily. But it smoked really bad. And it still does.
This might be the last time I see it running. I’m set to preform piston ring surgery first thing this spring.
Duration : 0:1:1
CARBURETOR Repair on Older BRIGGS & STRATTON 3.5HP Engine Part 2 of 2
Posted by admin
Reinstalling the carburetor and diaphragm. The final setting on Carb was 1 3/4 turn out.This is the same engine on the older lawnmowers with a Briggs & Stratton motor without a primer. Visit my channel for more repair videos. http://www.youtube.com/user/donyboy73?feature=mhw5
Duration : 0:6:39
Lister Two Cylinder Electric Start Diesel Generator
Posted by admin
http://starnetserver.com/Percy1234/GenDiesel
http://starnetserver.com/Percy1234/GenDiesel
One of my generators running. PepBoys 1200w Peak (850w rated). It’s quiet compared to other larger units and actually has a good sized muffler.
I wouldn’t run it overnight in a city neighborhood but, it’s quiet enough for day use. It’s has a two stroke 2hp gasoline engine that requires a 50:1 oil premix. And, it’s quite small. Compare it to the shop lamp in the video for size.
Lister Two Cylinder Electric Start Diesel Generator
http://starnetserver.com/Percy1234/GenDiesel
starting 1.6l single cylinder diesel generator.
Startup of GenDiesel 15KW Diesel Generator in Houston, TX. 713-851-7925
Newer 2010 model now available at www.EmergencyPower.com |
Remote Start Silent Diesel Generator 6500 Watt - Aurora makes the highest quality available anyplace.
http://starnetserver.com/Percy1234/GenDiesel
http://starnetserver.com/Percy1234/GenDiesel
http://starnetserver.com/Percy1234/GenDiesel
Duration : 0:1:10
18 HP Onan “No Start” and fix? on 1977 Craftsman GT18 Tractor
Posted by admin
I was told this machine wouldn’t run on anything but full choke. This video covers my work on the engine to figure out the problem.
My grandfather’s 1977 Craftsman GT18 Garden Tractor that is now mine. A rugged beast with an Onan 18 HP opposed twin engine connected to a hydrostatic drive. I believe the tractor was made for sears by Roper.
Duration : 0:8:56
CARBURETOR Repair on Older BRIGGS & STRATTON 3.5HP Engine Part 1 of 2
Posted by admin
Taking the Carb off, diaphragm and cleaning it. This is the same engine on the older lawnmowers with a Briggs & Stratton motor without a primer. Visit my channel for more repair videos. http://www.youtube.com/user/donyboy73?feature=mhw5
Duration : 0:7:5
Caterpillar start-up
Posted by admin
Starting a CAT with Donky Engine. Tractor & Machinery festival 5.6.2004 Stoneleigh showground.
Duration : 0:4:32
1987 Onan Generator Start up
Posted by admin
It has a bad choke.
Duration : 0:1:56